SKULL | GUNDAM | BOT DESIGN FOR YAMAHA AEROX V3 – YAMAHA AEROX VERSION 3 GUNDAM | BOT | SKULL DESIGN UPPERTAIL COVER STICKER- YAMAHA AEROX VERSION 3 UPPERTAIL COVER STICKER GUNDAM |BOT | SKULL DESIGN- AEROX V3 UPPERTAIL COVER STICKER GUNDAM |BOT|SKULL DES

SKULL | GUNDAM | BOT DESIGN FOR YAMAHA AEROX V3 – YAMAHA AEROX VERSION 3 GUNDAM | BOT | SKULL DESIGN UPPERTAIL COVER STICKER- YAMAHA AEROX VERSION 3 UPPERTAIL COVER STICKER GUNDAM |BOT | SKULL DESIGN- AEROX V3 UPPERTAIL COVER STICKER GUNDAM |BOT|SKULL DESIGN -MOTORCYCLE STICKER – MOTORCYCLE ACCESSORIES- EASY TO INSTALL-PREMIUM GLOSSY VINYL STICKER✨ PRODUCT FEATURES:-HIGH-DEFINITION PRINT-PREMIUM GLOSSY VINYL-PRECISION MACHINE CUT-ULTRASTRONG ADHESIVE-LAMINATED-100% WATERPROOF-FADE RESISTANTDRY INSTALLATION STEPS1. SURFACE PREPARATION (CRUCIAL STEP)• WASH THE TAIL AREA WITH DISHWASHING LIQUID AND WATER TO STRIP OFF WAX, OIL, AND SILICONE SPRAYS.• WIPE CLEAN WITH 70% ISOPROPYL ALCOHOL AND DRY COMPLETELY WITH A CLEAN MICROFIBER TOWEL.• MAKE SURE THERE IS ZERO DUST, GREASE, OR WAX—OTHERWISE THE ADHESIVE WILL PEEL AT THE EDGES.2. DRY FIT & HINGE TECHNIQUE• PLACE THE STICKER (WITH ITS BACKING PAPER STILL ON) DIRECTLY OVER THE TAIL AREA TO ALIGN IT.• ONCE ALIGNED, PLACE A STRIP OF MASKING TAPE ACROSS THE TOP CENTER OF THE STICKER TO CREATE A "HINGE."• FLIP THE STICKER UPWARD ON ITS HINGE TO CHECK THAT IT DROPS BACK DOWN IN THE EXACT RIGHT SPOT.3. PEEL & APPLY GRADUALLY• FLIP THE STICKER UP AND PEEL OFF ONLY 1–2 INCHES OF THE BACKING PAPER FROM THE TOP EDGE.• FLIP IT DOWN AND PRESS THE EXPOSED TOP ADHESIVE DOWN FIRMLY.• SLOWLY PULL THE REMAINING BACKING PAPER DOWNWARD WITH ONE HAND WHILE USING YOUR OTHER THUMB (OR AN ATM CARD WRAPPED IN CLOTH) TO PRESS THE STICKER ONTO THE PANEL FROM THE CENTER OUTWARD.4. SMOOTH OUT AIR BUBBLES• WORK IN SMALL SECTIONS, SWEEPING FROM THE CENTER TOWARD THE OUTER EDGES TO PREVENT TRAPPING AIR.• IF A SMALL BUBBLE FORMS, PULL BACK THE VINYL SLIGHTLY BEFORE IT FULLY ADHERES, THEN PRESS IT BACK DOWN SMOOTHLY.5. HEAT-SEAL THE EDGES (ESSENTIAL FOR CURVES)• WARM THE INSTALLED DECAL WITH A HAIRDRYER (OR QUICKLY PASS A LIGHTER 5–6 INCHES AWAY).• THE HEAT SOFTENS THE VINYL, LETTING YOU FIRMLY PRESS DOWN ON CURVED CONTOURS AND EDGES SO THEY DON'T LIFT LATER.PRO TIPS FOR DRY APPLICATION• AVOID WINDY OR DUSTY AREAS SO NO FLOATING DUST SETTLES ON THE ADHESIVE WHILE YOU WORK.• DON'T STRETCH THE VINYL TOO HARD WHILE PULLING, OR THE GRAPHICS MIGHT WARP OR LIFT OVER TIME.• IF ANY TINY AIR BUBBLES REMAIN, POKE A TINY PINHOLE AT THE EDGE OF THE BUBBLE AND PRESS THE AIR OUT TOWARD THE HOLE.#AEROXV3 #YAMAHAAEROX155 #AEROX155V3 #AEROXV3CONNECT #AEROXNATION #YAMAHAAEROX #AEROXPH #SCOOTERLIFE #AEROXCUSTOM #YAMAHAPHILIPPINES #UPPERTAILSTICKER #CHARACTERDESIGN #BOTDESIGN #SKULLDESIGN #MOTORCYCLEACCESORIES #MOTORCYCLESTICKERGUNDAM-GRAY