WenQia 433MHz Wireless Remote Control Switch 2 CH DC 12V 24V 36V 48V Type-C 5V RF Relay Module for Light/Fan/Motor/Garage Door Opener

Dear customer: In order to meet the needs of different customers, we have set up multiple options for you to choose from. Please be careful not to purchase the remote control separately. Thank you.433MHz Wireless Remote Control Switch 2 CHDC 12V 24V 36V 48V Type-C 5VRF Relay Module for Light/Fan/Motor/Garage Door Opener ...▶Supports 5 operating modes and has a very wide range of applicationsMomentary Mode / Toggle Mode / Latched Mode / Mix Mode / Motor Toggle Mode●Remote control desk lamps\AC or DC LED lights\bulbs\electric curtains\water pumps\fans\ventilation devices\signal transmission●Remote control garage door\electric door\house door\rolling door\telescopic door\gate\barrier gate●Remote control motor forward and reverse\motor switch\DIY●DIY various manual switches so that your switches can achieve remote control functions. For example, if your garage door remote control switch is lost or damaged, you can use our products to modify it.▶Examples of application scenarios:for remote control lights/fanfor remote controlled motors/garage door opener ▶50 meters control distance: The signal is stable and can pass through walls, and the pairing is flexible. The remote control distance can reach 50 meters (in an open area).One receiver can be paired with up to 20 remote controls.▶ Relay Receiver Board ParameterWorking voltage  :  DC7~48V-0.5A or AC 12~36V or USB Type-C 5V-0.5AInput vlotage  :  1~250VOutput vlotage  :  1~250VQuiescent Current  :  <5MAMax current  :  10AMax load:   2200WRF frequency  :  433MHzPin  :  NO / COM / NCWorking temperature  :  -30~+80 CelsiusReceiving Sensitivity  :  >-97dbmAmount of storage remote controls  :  20 piecesSupport encoding  :  1527 Learning codeRF Operating mode  :  ASK superheterodyne wireless receptionReceiving range  :  Open space is more than 1000 metersRemote operating mode : Momentary Mode/ Toggle Mode/Latched Mode/Mix Mode/Motor Toggle ModeNC:Normally closed pinCOM:Common pinNO:Normally open pin▶ Remote controllerParameter  RF frequency : 433MHzControl Distance : 50 meters in open spaceMaterial : PlasticSupport encoding : 1527 Leaning codeBattery  : CR2032 includedSize:345910 mm ▶ 2 types of power supply methods  ▶ Wiring diagram Various wiring methods, here are 4 examples.You can actually have more ways of wiring.If you have any questions, please contact us, we will try our best to answer, thank you.▶ Operation Mode●Momentary Mode:1. Press and hold the button"A", relay "1" will turn on;2. Release the button"A", this relay "1" will turn off.In the same way, the button"B" can control relay"2" Set up:Click learning button on the receiver 1 time ,click the button"A" 1 time,click the button"B" 1 time,succeed●Toggle Mode:1. Press the button"A", relay "1" will turn on;2. Press the button"A" again, this relay "1" will turn off.In the same way, the button"B" can control relay"2" Set up:Click learning button on the receiver 2 times ,click the button"A" 1 time,click the button"B" 1 time,succeed●Latched mode(This mode requires a remote control with at least 3 buttons or more):1.Press "A" key, relay "1" will turn on;2.Press "B" key, relay "2" will turn on, at the same time relay "1" will turn off.3.Press "C" key, Both relays "1" and "2" will turn off.Set up:Click learning button on the receiver 3 times ,click the button"A" 1 time,click the button"B" 1 time,succeed●Mix Mode:1.Press and hold the button"A", relay "1" will turn on; Release the button"A", this relay "1" will turn off.1.Press the button"B", relay "2" will turn on;Press the button"B" again, this relay "2" will turn off.Set up:Click learning button on the receiver 4 time ,click the button"A" 1 time,click the button"B" 1 time,succeed●Motor Toggle Mode:1.Press the button"A", relay "1" will turn on, Press the button"B", relay "2" will turn on, at the same time relay "1" will turn off.  Press the button"B" again, relay "2" will turn off.1.Press the button"B", relay "2" will turn on, Press the button"A", relay "1" will turn on, at the same time relay "2" will turn off.  Press the button"A" again, relay "1" will turn off.Set up:Click learning button on the receiver 5 time ,click the button"A" 1 time,click the button"B" 1 time,succeedReset 1.Press learning button 8 times to clean data,then all remotes can not control this receiverNotice: 1. Reset before you want to change the operating mode of one remote control.2. After reset, all the remote controls can not work anymore.3. Replace the battery in time when the remote control voltage is low. To get the stronger signal transmission.▶Please contact with us if you have any questions.Thank you.▶We have own factory,if you want to do ODM OEM bussiness,please contact with us.